EV also called Reconstituted veneer ,is manufactured using real wood but not the actual wood of the wood species.  

Engineered Veneer (EV) combines non-tropical raw materials with state of the art manufacturingtechnologies, to produce high quality veneers for the surfaces of hardwood plywood products, which wouldpreviously have used potentially higher risk (in relation to EUTR) tropical veneers. EV was initially developedfor the decorative veneered plywood market, but the technology has now been successfully applied to theproduction of commercial veneers for the high volume plywood market. The result is an environmentallyfriendly product, sourced from close to the production mills, rather than from overseas suppliers to theChinese market such as Malaysia, Solomon Islands or Papua New Guinea.

Log Selection
EV is generally produced from Chinese Poplar logs, grown locally either by local co-operatives,or in registered plantation areas. The light natural colour and soft grain definition of Poplar makes it wellsuited to the production of EV. The process of converting timber into EV starts with the selection oflogs, following which they are bought to the mill for processing. The timber is trimmed, sawn to length and debarked. The logs are now ready to be peeled.

Peeling of the Logs
The logs are mounted onto a giant lathe. Within minutes the logs are peeled into rotary veneers. This is achieved by pressing a rotating log towards a large blade, thinly peeling a continuous sheet of veneer off the log. The veneer is dried, stacked and then graded. It is now ready to be dyed.

EV veneers can be dyed to a consistent colour to suit the market requirement. The raw veneer leaves are stacked into a stainless steel cage. Once completely loaded, the stainless steel cage is immersed into a pressurized, heated vat that is filled with water soluble dye. This system ensures that each leaf is given the correct amount of time to allow the dye to completely penetrate each individual leaf of veneer. Once the desired colour has been achieved, the leaves are unloaded from the vat, dried and given a final inspection before going to the gluing stage.

The gluing process is critical for the performance of the finished product. A layer of glue goes between each leaf of veneer, to bond the leave of veneer together. Once the stack has been laid up it is then put into a high pressure press to bond the leaves together, creating a large rectangular block.

Slicing of the Block
The block in now ready to be sliced into veneer leaves. Once the block has been produced, it is turned through 90 degrees, to present the end grain, then mounted to the slicing unit. The blade now runs across the end grain of the block, slicing thickness controlled leaves of veneer. The veneer leaves that are produced are approximately 0.4mm thick, and in 640mm x 2460mm format. The veneer is now ready to be used as face veneer for plywood products.

May you have the following questions about the EV veneer ,

reconstituted veneer suppliers,

recon veneer price,

reconstituted walnut veneer,

types of reconstituted wood,

veneer manufacturing process,

reconstituted ebony veneer,

veneer lamination process,

echo wood reconstituted veneer,

Special thanks to the original source of

1. (I can remember this is the orignal source ,but could not open the website anymore ,but really thanks for the knowledge of the Meyer timber as I learned new words from the webstie ) 

如无特殊说明,文章均为本站原创,转载请注明出处。If there are no special instructions, the articles are original, if you want to use or reproduce, please indicate the original source,If you find that our articles infringe on your copyrights and interests, please email us at in time and we will delete it at the first time.

Check Also

Veneers & Edgebanding Inspection,Testing ,quality Control,sourcing

Veneers & Edgebanding 2 Ply Wood Veneers Any Specie Wood Veneer Edgebanding Polyester Edgebanding 如无特殊说明,文章均为本站原创,转载请注明出处。If …

Leave a Reply

Your email address will not be published. Required fields are marked *