H20 Concrete Formwork Beam Inspection Checklist and Grading Rules

H20 Concrete Formwork Beam Inspection Checklist and Grading Rules

Dimensions standards:  80 x 200 x 2450,2900,3300,3600,3900,4200,4900,5900 mm

The Destil H20 Timber   beams    available with plastic protection (protective cap) represents the natural construction tool in the shuttering process. Entirely made of massive wood in a totally mechanised way, The beam is handy, strong and versatile. It can be used both as primary beam, both as secondary beam in the realisation of concrete roofs, both as support in wallmaking shuttering systems.The beam constitutes a complete shuttering system finding its main usage in the realisation of any type of concrete roof.
– Indeformability;
– Dimensional stability;
– Lightness and handiness;
– High resistance to athmospheric agents;
– Long durability thanks to high quality glueing;
– Saving on time and cost of manufacturing;
– Large range of usages;
– Easy disposability;
– Protection from accidents thanks to round edges.

H20 concrete formwork beams of SPRUCE and FIR and PIne. The wing is made of carefully selected quality wood.

The core consists of a 3-layer panel, which ensures the stability of the beam and allows it to withstand all weather conditions.

Wing assemblies and core are inseparably joined by a splice.

Optional: plastic protective cap, shock resistant. Placed at the ends of the beam, this adapter provides additional protection against mechanical damage. This allows the beam to be reused several times and prolongs the beam’s life span while improving it’s strength.

The surface of the beams is protected by a waterproof coating which guarantees a long lifespan.

For greater ease of use, the length is indicated on each beam (beams are 20cm high and are produced in various standard lengths).

PROPERTIES Cheaper and high quality product for formwork
Excellent flexural strength
Minimal distortion
Waterproof and water resistant
Comes from sustainably managed China forests (FSC)
MATERIAL SPRUCE and FIR,PINE
DRYING KD 12 +/- 2%
WEIGHT 4,7Kg/m
BOND Hot glue, melamine resin
WINGS • Made of Spruce ,Pine or Fir, carefully selected
• The wing and the core are assembled by a joint splice and are bonded crosswise (relative to the rings)
• the cross dimensions are 80 x 40 mm
• The wings can be joined together in length
• The wing is milled along its core
• The edges of the wing are planed and chamfered (up to about 0.4 mm)
CORE 3 layered Plywood plate bonded so that the rings are vertical (relative to the cross section)
TREATEMENT The surface is completely protected by a waterproof and water-repellent coating
ADAPTABILITY With 3 layers in the core, the H20 beams can be cut to any length, without their properties being altered.
STANDARD LENGTHS 1,95 / 2,45 / 2,65 / 2,90 / 3,30 / 3,60 / 3,90 / 4,50 / 4,90 / 5,90 / maximum length: 6,00 m
DIMENSIONS AND DEVIATIONS
Dimension Value Gap
Depth of the joist 200mm +/- 2mm
Depth of the wing 40mm +/- 6mm
Width of the wing 80mm +0,8 / 1,2mm
Thickness of the wing 29mm +/- 0,87mm
TECHNICAL CHARACTERISTICS

The values shown are valid for new formwork beams that have not yet been used, stored in suitable and properly used conditions. For beams which have been used several times, it is necessary (depending on different uses and requirements thereof) adding a proportional safety factor.

 

Check Also

Film faced plywood Physical and mechanical parameters

Film faced plywood Physical and mechanical parameters Parameter Measurement unit GOST 3916.1-96 EN Actual value …

Leave a Reply

Your email address will not be published. Required fields are marked *