Veneer Grades

Veneer Grades

Veneer in a finished US trademarked plywood panel must conform to one of the six grades listed in the US PS 1-09 standard: N, the highest classification (rarely produced), followed by A, B, C-plugged, C and D.

See veneer grades for Popular APA Plywood Panels.

The requirements given here apply to panels measuring 2440mm (96”) x 1220mm (48”) and are proportionate for other sizes.

APA has produced two easy to follow guides to help match the grade numbers given on a US finished plywood panel with the requirements of  EN 635-3.

Detailed guide (below) listing permissible defects – with maximum sizes.

Simplified guide to the US PS 1-09 veneer grading rules and appearance grades in EN 635-3 based on the appearance of the surface veneers. Equivalents cannot be exactly compared as two different sets of grading rules apply.

Veneer Grade Description Permissible defects  – maximum sizes


(rarely produced)

Should be smoothly cut and be either 100% heartwood or 100% sapwood, free from knots, knot holes, pitch pockets, open splits, other open characteristics and stain.  The veneer must consist of not more than two pieces in 1220 mm (48”) widths and not more than three pieces in wider panels; and be well matched for colour and grain.  When panels are sanded no sander skips are permitted.


Must be firm, smoothly cut and free from knots, pitch pockets, open splits and other open characteristics.  If consisting of more than one piece, they must be well jointed.  When panels are sanded, no sander skips are permitted.
Knots Not allowed
Open knots/holes Not allowed
Splits Not allowed
Grain Smooth
Repairs May be a max of 18 wood parallel to the grain or synthetic


Must be solid and free from open characteristics and broken grain, except as permitted e.g. where there are knots or splits.
Knots 25.4mm (1”).  Must be sound & tight
Open characteristics 1.6mm (1/16”)
Splits 0.8 mm (1/32”)
Repairs permitted (unlimited) wood or synthetic
Sander skips permitted up to 5% of panel


Tight knots Up to 38.1mm (1-1/2”) no limit
Knot/ open holes 25.4mm (1”) max. With an occasional up to 38.1 mm (1-1/2”) across grain
Splits Measured at 203mm (8”) from panel end – not to exceed 12.7mm (1/2”) in width by ½ panel length, or 9.5mm (3/8”) width by any panel length, provided separation at one end no greater than 1.6 mm (1/16”)
Repairs Permitted in wood or synthetic
Discolouration Permitted


Improved C veneer
Open 6.4 mm (1/4”) x 12.7mm (1/2”)
Tight knots Up to 38.1mm (1-1/2 “)
Splits Limited to 3.2mm (1/8”) width
Broken grain Permitted but limited
Repairs Synthetic and wood permitted
Touch sanded may be fully sanded


Knots Up to 63.5mm (2-1/2”) width across grain.  Occasional tight knot up to76.2mm (3”)
Open knots/ holes Up to 63mm (2-1/2”) width across grain
Splits Measured at 203mm (8”) from panel end, not to exceed 25.4mm (1”) tapering to not more than 1.6mm (1/16”) where running full panel length. Splits on panel faces 6.4mm (1/4”) width where located within 25.4mm (1”) of parallel panel edge.
Broken grain Permitted
Wane When not exceeding 203mm (8”) length width of wane may be up to 76.2mm (3”) pending location in panel.
D Grade veneers are not permitted in Exterior grade panels

veneer grading rules and appearance grades in EN 635-3 based on the appearance of the surface veneers.

 US PS 1-09 Standard

 EN 635-3 (Softwood)

C plugged


如无特殊说明,文章均为本站原创,转载请注明出处。If there are no special instructions, the articles are original, if you want to use or reproduce, please indicate the original source,If you find that our articles infringe on your copyrights and interests, please email us at in time and we will delete it at the first time.

Check Also

Engineered Wood Veneer and Natural Wood Veneer inspection,quality control ,sourcing ,testing

Differences between Natural and Engineered Wood Veneers Wood veneers are attractive and rightfully popular materials …

Leave a Reply

Your email address will not be published. Required fields are marked *