Wood Veneer Matching

Wood Veneer Matching,Veneer Cutting & Matching ,wood veneer Technical info,Glossary of Veneer Terms,Veneer Technical Guide, Veneer Selection





Architectural Grade

Utilizes top quality veneer and generally has special requirements for balancing, sequencing, component width, etc.




The lowest grade veneer which is generally only used as cross band veneer or for non-visible surfaces.


The term given to the small to large eye-shaped marking of figure found throughout select sheets of Maple.

Block Mottle Figure

An irregular form of figuring which runs over the complete surface of the veneer.

Barber Pole

The noticeable color variation that occurs when a distortion of the grain is created by the knife blade. The knife blade, as it hits the wood, creates a “loose” side where the cells have been opened up by the blade and a “tight” side. Because the “tight” and “loose” faces alternate in adjacent pieces of veneer in book matching, they may accept stain differently.



Bark Pocket

A small area of bark around which normal wood had grown.

Blue Stain

Blue stains on the surface of the veneer which occur through insufficient water extraction when slicing (too low heating capacity on the pressure bar or when slicing too fast) because water remaining on the surface of the veneer turns blue through oxidation.

Book Match

The most commonly used match in the industry. Every other piece of veneer is turned over so adjacent pieces are opened like two adjacent pages in a book. The veneer joints match and create a mirrored image pattern at the joint line, yielding a maximum continuity of grain. Book matching is used with flat cut, quarter, rift or rotary cut veneer.


Corrugation in the veneer leaf resulting from different drying runs and irregular annual ring development. The veneer has to be flattened again to make the veneer saleable.


A group of cut veneer leaves generally containing 24 or 32 consecutive sheets.


Burls feature swirling grain around clusters of dormant buds, rings or eyes. Available in White Ash, Olive Ash, Carpathian Elm, Maple, Mappa, Myrtle and Walnut.



Cathedral Structure

Much sought after structure in flat cut or plain sliced bundles.

Chatter Marks

Deviation in veneer thickness caused by vibration of the veneer block on the slicing machine, an incorrect pressure setting on the slicing machine or an incorrect setting on the sander. The resulting marks on the veneer leaf are regularly distributed cross-running stripes.


Small slits running parallel to the grain of the wood, caused chiefly by strains produced in seasoning.

Comb Grain

A quality of rift veneer with exceptionally straight grain and closely spaced growth increments.

Component (of Face)

An individual piece of veneer that is jointed to other pieces to achieve a full length and width face.


Type of figure or irregularity of grain resembling a dip in the grain running at right angles, or nearly so, to the length of veneer.

Cross Break

Separation of the wood cells across the grain. Such breaks may be due to internal strains resulting from unequal longitudinal shrinkage or to external forces.


Veneer sheet in which the grain of the wood runs in the 4′ direction. This is denoted as 8’x4′. Width is the measurement across the grain, while length is the measurement with the grain. The first number is always the width and the second is the length.


Cut from the juncture of a tree’s main branches and trunk, crotch figures are often subcategorized as flame, plume, rooster tail, feather or burning bush. Available in Mahogany.




The separation of veneer in plywood through failure of the adhesive.


Stains in wood substances. Common veneer stains are sap stains, blue stains, stains produced by chemical action caused by the iron in the cutting knife coming in contact with the tannic acid of the wood and those resulting from the chemical action of the glue.




Leaves of veneer that have been spliced together, but have not yet been applied to a panel or backer sheet. Also, the better side of any plywood panel in which the outer piles are of different veneer grades.

Fiddleback Figure

Narrow bands of figure that run uninterrupted from edge to edge across the width of the veneer leaf. When book matched, a chevron pattern is formed. Most commonly available in Anegre, Maple, Makore and English Sycamore.


The pattern produced in a wood surface by annual growth rings, rays, knots, deviations from natural grain such as interlocked and wavy grain and irregular coloration.


Markings across the grain of the face. In book matched material, the markings seem to extend across the width of the face.


Varies in size from “dash marks” to “stretch marks.” Created when the pithrays are cut across at an angle when slicing. Very common in Quartered Red and White Oak.

Flat Cut

The half log, or flitch, is mounted with the heart side flat against the flitch table of the slicer and the slicing is done parallel to a line through the center of the log. Cathedral and straight grain patterns result.


The complete bundle of thin sheets of veneer after cutting, laid together in sequence as they were sliced or sawn.




The direction, size, arrangement and appearance of the fibers in wood or veneer. The 8′ grain direction in 4’x8′ veneer and plywood.


Black spots or patches which can occur in Black Cherry veneer. They are not arranged in a regular pattern but can be positioned quite differently from one veneer leaf to the next.

Gum Pockets

Well defined openings between rings of annual growth, containing gum or evidence of prior gum accumulations.

Gum Spots

Gum or resinous material or color spots caused by prior resin accumulations sometimes found on panel surfaces. Gum spots can often be removed by sanding.





General term used to designate lumber or veneer produced from broad-leafed or deciduous trees. This is in contrast to softwood, which is produced from evergreen or coniferous trees.


The non-active center of a tree generally distinguishable from the outer portion (sapwood) by its darker color.



Jet Drier

Veneer drying machine which dries the veneer in a continuous operation using hot air.


The line between the edges of two adjacent leaves of veneer.

Joint, Open

Joint in which two adjacent pieces of veneer do not fit tightly together.




Cross section of a tree branch or limb with the grain usually running at right angles to that of the piece of wood in which it occurs.

Knot, Open

Opening produced when a portion of the wood substance of a knot has dropped out.

Knots, Sound, Tight

Knots that are solid across their faces and fixed by growth to retain their place.




A condition where one piece of veneer in the same ply overlaps an adjacent piece. Face manufacturing defect.


Sliced sheet of a veneer flitch.


The section of a tree that can be sawn or used for veneer.

Loose Side

In knife-cut veneer, the side of the sheet that was in contact with the knife as the sheet was being cut. It contains cutting checks (lathe checks) because of the bending of the wood at the knife edge.



Matched, Balance

The width of each veneer leaf in a panel face is the same. Panels may contain an even or odd number of leaves and distribution may change from panel to panel within a sequenced set. This reduces veneer yield.

Matched, Reverse Slip

In reverse slip matching the veneer leaves are slipped out from under each other and every other veneer leaf is flipped end to end. This balances the character of the veneer in the panel face.

Matched, Running

Each panel face is assembled from as many veneer leaves as necessary so that the widths and number of matching veneer leaves are not requirements. This can produce a match which appears less even or random and asymmetrical.

Matched, Book

The most commonly used match in the industry. Every other piece of veneer is turned over so adjacent pieces are opened like two adjacent pages in a book. The veneer joints match and create a mirrored image pattern at the joint line, yielding a maximum continuity of grain. Book matching is used with flat cut, quarter, rift or rotary cut veneer.

Matched, Center

An even number of equal width veneer leaves make up a panel face. Thus, there is a veneer joint in the center of the panel. This match further reduces veneer yield.

Matched, End

This type of matching is often used to extend the apparent length of available veneer for high wall panels and long conference tables. A sketch or drawing is required for quoting, as there are several different ways to achieve this result.

Matched, Slip

Adjoining pieces of veneer are placed in sequence without turning over every other piece. The grain figure repeats, but joints will not show mirrored effect. Slip matching is often used in quarter cut and rift cut veneer to minimize the barber pole effect.

Matched, Random

Two or more pieces of unequal size or from different flitches in a single face.


Medium Density Fiberboard (MDF)

A panel or core product manufactured from wood fibers combined with a synthetic resin or other bonding system.



Dark patches or pockets in wood.




Open Defect

Faults in veneer which produce holes.



Particleboard (PBC)

A panel or core product composed of small particles and wood fiber that are bonded together with synthetic resin adhesives in the presence of heat and pressure.



Intersections of sound wood plugs or shims placed and taped into veneer faces to fill small voids.

Patches, Inconspicuous

Elongated patches which are similar in color and grain to adjacent wood so as to blend well.


The thin black knots in Yew veneer which are the typical figuring of Yew veneer. The more pepper there is and the more regular this pepper is distributed over the surface the more valuable the veneer.

Pin Knots

Small knots found throughout the veneer sheet.


Plain Sliced

The half log, or flitch, is mounted with the heart side flat against the flitch table of the slicer and the slicing is done parallel to a line through the center of the log. Cathedral and straight grain patterns result.

Plywood (Veneer Core)

A assembly made of layers (plies) of veneer, or of veneer in combination with a solid core, joined with an adhesive.



A dense pattern of small rings enveloping one another. Often described as looking like “suede” or “fur.” Most commonly available as Sapele.




The quarter log is mounted on the flitch table so that the growth rings of the log strike the knife at approximately right angles, producing a series of stripes. These stripes vary in width from species to species. A natural distribution of ray flake is a characteristic of this cut in red and white oak.




The cut slices slightly across the medullary rays, accentuating the vertical grain and minimizing the flake. Rift grain is restricted to red and white oak.

Rotary Cut

The log is mounted centrally in the lathe and turned against a razor sharp blade, like unwinding a roll of paper. Since this cut follows the log’s annual growth rings, a bold variegated grain marking is produced. Rotary cut veneer is exceptionally wide.



Rough Grain

Irregular shaped areas of generally uneven corrugation on the surface of veneer, differing from the surrounding smooth veneer and occurring as the veneer is cut by the lathe or slicer.




The outer cell layer of the wood between the bark and heartwood. The supply of water and nutrients to the tree is only through the outer row of sap cells. The remaining layers of cells in the sapwood only serve to store water. Color is offset in sapwood. The sapwood is cut away in veneer.


Sequencing refers to a set of veneer sheets that have been produced in order from the same log. The number of sheets per sequence can be limited by species, cut, grain-orientation and yield.


Cracks in the lumber which follow the annual rings. Parts of trunks with this defect are not suitable for producing veneer or sawn timber.


A distinct kind of wood.



Split Heart (Manufactured Cathedral)

A method of achieving an inverted “V” or cathedral type figure by joining two “flat-cut” face components of similar color and grain.


Color changes in the log when it has been stored too long. Direct radiation from the sun or too dry an atmosphere furthers this development.

Stripe, Broken

Broken stripe is a modification of ribbon stripe with the markings tapering out and producing a broken ribbon.

Stripe, Ribbon

In some woods, such as Mahogany, wide unbroken stripes can be produced by cutting on the quarter.



Tight Side

In knife-cut veneer, the side of the sheet was farthest from the knife as the sheet was being cut. It contains no cutting checks (lathe checks).

To Split

Cutting a log to the required length using the desired method of slicing.

Turning Veneer

The presentation of a log which is shown bundle by bundle.



Underground Burl

Burl log where the burl development is in the root and the burl is either completely or partially under the ground. These logs have to be dug out to obtain them, an operation which is generally done by hand in order not to damage high quality burls. Underground burls are Myrtle, Walnut, Maple, and Redwood Burl.




The pit used for steaming or cooking logs.


A thin sheet of wood, rotary cut, sliced, or sawed from a log, bolt or flitch. Veneer may be referred to as a ply when assembled into a panel.

如无特殊说明,文章均为本站原创,转载请注明出处。If there are no special instructions, the articles are original, if you want to use or reproduce, please indicate the original source www.plywoodinspection.com,If you find that our articles infringe on your copyrights and interests, please email us at info@plywoodinspection.com in time and we will delete it at the first time.

Check Also

Differences between Natural and Engineered Wood Veneers

Differences between Natural and Engineered Wood Veneers Wood veneers are attractive and rightfully popular materials …

Leave a Reply

Your email address will not be published. Required fields are marked *